Dixie Canner Co - Dixie's 221P R&D Vacuum Seamers

VACUUM to 29" Hg · GAS FLUSH
MULTIFLUSH · TIMED DELAYS

Endless Possibilities!

RANGE:
2" to 6-1/4" diameter up to 7" tall.
Option for taller cans.

FLOOR SPACE: 28" x 24"

HEIGHT: 73" or 81"

SHIPPING: 500 or 575 pounds

They're FAST,
PRECISION,
TOUGH ...

Model UVGMD-ALCC Dixie 221P R&D Vacuum Seamer with .65 HP gearhead motor drive and electrically controlled clutch/brake/air lift/gas/timed delays/multiflush system, including vacuum pump rated 29.8" Hg with 1.25 HP motor, filter, Command Center, digital vac/gas Programer and gassing attachment (no tank or regulator), 110/115 VAC, 50/60 Hz, 20 Amps.
Customized to close ONE SIZE can .......................................................	$24,300.00
Customized to close ONE SIZE can over 7" tall with 15" chamber..............	$30,300.00

OPTIONS:
Customized to close 6 5/8" diameter cans or smaller than 2" dia. ..............	ADD $ 800.00
Transformer/vacuum pump for 220 volts, 50 Hz, 1-phase............................	ADD $1,375.00

EXPORT BOXING (7" Chamber) .............................................................	$ 750.00
EXPORT BOXING (15" Chamber) ...........................................................	Request Pricing

ADVANTAGES:

1. Set vacuum and gas values to 29" (725 mm) Hg

2. Set vacuum and gas flush to 9 cycles

3. Set vacuum and gas timed delays from 0.1 to 10 seconds

4. Set to close after gassing or after vacuum

5. Counts cans closed in four (4) Operating Functions

6. Reminds the operator to Clean and Oil after 5,000 cans

7. Change from one can to another and reset controls in minutes ... or seconds.

8. Four Operating Functions and 221 Program Steps say the possibilities are endless!

No. 648 Digital Vacuum and Gas PROGRAMER, located on the right side of the vacuum chamber, in easy reach. P1 – 15 (shown) and P3 are VACUUM set values. P2 and P4 are GAS set values. Values are displayed then set as the button or key is pressed with your finger.

Millimeter values may be displayed.

TO OPERATE: Press Function key. Position a filled can and top, and the set values, cycles and timed delays are performed precisely and repetitiously each time the chamber door is closed, and before the can and top are joined and hermetically seamed. Requires compressed air.

They're tough, fast, precision .... Tough enough to can heavy welding rods ... Precision enough to extract oxygen from dense powders and to produce hermetic seams, time after time, after time.

They're made of rust resisting materials which may be wiped clean and sanitized.

Your cans may vary in size, type and style. You may seam cans atmospherically. You may vacuum and close. You may gas flush, multiflush or you may program delays before closing ... In ONE seamer which has a digital vacuum/gas PROGRAMER and Dixie's Multiversa COMMAND CENTER with a Tactile Keyboard and screen. And they're designed for continuous operation.

Vacuum expels oxygen to prolong shelf life of the can's contents. So, if vacuum may collapse the can ... with the touch of a finger ... you may set the controls for a gas flush. Or multiflush, or set timed delays between each flush to determine the best set values for dense powders, products, supplies and new productions that come to market daily.

To change from one can to another and set controls for another operating function takes only minutes ... or seconds. And, if needed, Dixie factory assistance takes only a phone call, fax or email message from you. "No problem." Guaranteed.

CAPACITY: (Estimated, based on 18" Hg)
		Vacuum Chamber
		7"		15"
Operating Functions:	F1 Atmospheric:	10	Cans Per Minute	8
	F2 Vacuum Only:	8	Cans Per Minute	6
	F3 Vac/Gas Flush:	6	Cans Per Minute	5
	F4 Multiflush (3):	3	Cans Per Minute	2